It’s annoying to misplace your television remote. It might be inconvenient to have to go through the full setup procedure again.
Fortunately, Xfinity remotes are not like other remotes. They are also quite simple to link with your television, due to the online remote code search.
To pair your Xfinity remote with your TV, Open the online code lookup tool, choose the model of your Xfinity remote and the brand of your TV, then complete the setup using the code you obtain.
We’ll look at how to program the X1, XR11, and XR15 remotes for your TV in this post, as well as answer some commonly asked questions concerning Xfinity remotes.
Using the Online Code Lookup Tool, program the X1 Remote for TV and Audio.
You can program your X1 remote for both your TV and audio devices. To do this, all you need to do is go to Xfinity’s official website and find the Xfinity Remote Code Lookup Tool.
Pick the model of the remote that you own and press continue to find your TV’s (or audio system’s) unique code.
For Remotes with a Setup Button like The XR11
- Press and hold the setup button until the status LED at the top of the remote turns green.
- Enter the four or five-digit code you found using the remote code search tool once the remote is in setup mode.
- The status LED will blink green twice once the setup is successful.
Note: Try using different if the status light blinks red.
For Remotes without a Setup Button like The XR15
While the TV is turned on:
- Press and hold the Xfinity and mute buttons together until the status LED at the top of the remote flashes green.
- Enter the four or five-digit remote code that you found earlier
- If the status LED flashes to green twice, it indicates that the setup was successful.
Note: Try using different if the status light blinks red.
Pair the XR11 Remote to A TV
You can pair the XR11 remote to your TV without using the remote code search tool by doing the following:
- Turn on the television.
- Switch the TV input to the one linked to the Xfinity TV Box.
- Hold down the Setup button until the status LED at the top of the remote changes to green.
- On the remote, press the Xfinity button. The status LED will start to glow green.
- Input the three-digit pairing code shown on the screen.
- Your XR11 remote is now linked to your television.
Pair the XR15 Remote to A TV
To pair the XR15 remote to your TV without using the remote code lookup tool, you can follow these steps:
- Turn on the television.
- Switch the TV input to the one linked to the Xfinity TV Box.
- For roughly five seconds, press and hold the Xfinity and info buttons together until the status LED at the top of the remote turns green.
- Input the three-digit pairing code shown on the screen.
- Your XR15 remote is now linked to your television.
- Once the remote has been properly linked, follow the on-screen directions to set up your TV’s power, volume, and input control.
Remove the TV and audio receiver controls.
To remove TV and audio receiver control:
- Press and hold the Setup button on your remote until the status LED at the top of the remote turns green.
- Enter the code 9-8-6.
- The status LED at the top of the remote will flash green twice to indicate that the remote has been successfully reset.
If this doesn’t work, fully reset your Xfinity Remote.
Sync your Xfinity Remote to your TV.
Setting up your Xfinity remote with the remote code search tool is a quick and easy procedure.
It’s worth noting that each TV manufacturer has numerous remote codes.
So, if one code does not work, you do not need to be concerned. You can always try another code.
If none of the codes work for you, there may have been an error during setup, and you will need to do a factory reset on your remote before you can set it up again.
Frequently Asked Question
- XR11, XR5, or XR2 have a setup button and The button’s location is a little different depending on the remote type, but it should say ‘Setup’ below the button on all of the remotes.
- XR15 Remotes have no setup button
How do I program my Xfinity XR15 remote without a code?
What are the codes for Xfinity remote?
How do I reprogram my xr15 remote?
Press and hold the A [triangle] and D [diamond] buttons on the remote until the status light changes from red to green. This takes around five seconds. To complete the factory reset, use your remote to dial 9-8-1. After that, you may try pairing your XR15 remote again.