Why Samsung TV Remote Not Working Blinking Red Light – How to fix it?

If you have a Samsung TV, you may have noticed that the remote control’s blinking light stops. This can be frustrating, especially if you’re in the middle of watching a movie or TV show. There are a few things you can ensure to prevent your remote from stopping blinking, in any case. In this work, we’ll demonstrate to you how to keep your Samsung remote from stopping blinking.

We will examine a few of the most common blinking problems with Samsung remote controls and what you can do to fix them. We’ll also give you tips on preventing these problems from happening in the first place. By the end of this essay, you’ll comprehend how to keep your Samsung remote in good working order for years to come.

Note: sometimes remote red light blinking is directly connected to your Samsung TV blinking red light issue, therefore you should check it out to see if there is any fixed for you. 

Reasons Why Samsung TV Remote Not Working Blinking Red Light

1. Dead Batteries:

This is the most common reason your Samsung remote is blinking. This may seem apparent, but you’d be amazed at how frequently it is forgotten.

Poor or failing cells might also lead your remote to stop responding and begin glowing red. If somehow the cells are not fully charged, the controller will not function correctly. Swap the batteries and see if that fixes the problem.

2. Dirty/Corroded Contacts:

Quite often, the remote isn’t fully damaged, but one or two buttons are stuck.

Dust, filth, and rust develop throughout time, leading your remote to perform improperly or to malfunction altogether.

If the batteries are acceptable, the next thing to check is the contacts. If they are dirty or rusty, that could be what’s causing the problem. Try cleaning the links with a cotton swab or a paper towel to see if it solves the problem.

3. Bad Remote:

If the batteries and contacts are both fine, the remote itself may be terrible. In this case, you’ll need to buy a new remote.

4. Receiver Issue:

The receiver will likely have a problem if the remote works fine with other devices. For using your Samsung tv remote, you should first link it with your television. Throughout the setup process, the remote will seamlessly couple with the Television and will most likely be considered linked for some time. Try unplugging the receiver and working it back in. If that doesn’t work, you may require to replace the receiver.

5. TV Settings:

Finally, if none of the above solutions performs, the problem may be with your TV’s settings. Try reorganizing the TV to factory settings or see if there is a unique code you need to enter to get the remote to work.

6. Firmware Issue:

A firmware update may be desired for the remote to work correctly if your TV is connected to the internet.

7. Misaligned Remote:

 If the remote is not appropriately aligned with the TV, it may not work correctly. Try pointing the remote directly at the TV.

8. Distance:

The remote may not work if you are too far from the TV. Try moving closer to the TV and see if that fixes the problem.

9. Obstruction:

Whenever you attempt to operate the Samsung remote controller, it may stop functioning and begin flashing red due to a blockage between the controller and your Television.

When you attempt to operate the controller, it will indeed transfer signals. Nonetheless, the movements might not always approach the TV transmitter due to impediments

Simple activities in the living area, including noise bars, magazines, youngsters’ blocks, furniture, and so on, might obstruct your remote’s visible line of contact with the TV set.

 Make sure nothing is delaying the track between the remote and the TV. This could include furniture, curtains, or even people.

10. Physical damage:

Any mechanical disturbance to your remote might lead it to malfunction. The tv remote still may glow red, but it cannot function due to an insufficient wiring diagram on the chipset.

Because a remote is often used, typical wear and tear might lead it to defect throughout the period.

11. Check the Manual:

Consult your TV manual if you still can’t get the remote to work. It may have specific instructions for programming the remote or troubleshooting problems.

How to Fix a Samsung TV Remote that has a Blinking Red Light

A Samsung TV remote with a blinking red light indicates that the remote is blinking correctly. There are several ways to fix a Samsung TV remote with a blinking red light.

Battery Replacement

The first way to fix a Samsung TV remote with a blinking red light is to replace the batteries. If the batteries are not the problem, the next step is to check the remote control for physical damage. If the remote control is damaged, it will need to be replaced.

Remote Resetting

The second way to fix a Samsung TV remote with a blinking red light is to reset the remote control. To reset the remote control, press and hold the power button for five seconds. After five seconds, release the power button and press the reset button.

Reprogramming the Remote

The third way to fix a Samsung TV remote with a blinking red light is to reprogram the remote control. To reprogram the remote control, press and hold the power button for five seconds. After five seconds, release the power button and press the reprogram button.

Restart your Samsung Television

Energy cycling the Samsung TV might assist with a variety of difficulties. Furthermore, the procedure is both quick and straightforward. These processes are as follows:

Disconnect your television from the main socket.

Click and maintain the Power Key for a minimum of 1 min. This will deplete stored energy from the TV’s batteries, effectively initializing it.

Reconnect your TV to the socket. Then switch on the television and check your controller.

But unless energy cycling the TV didn’t help, you can try factory resetting this as a last resort to reset the controller. Remember that all your TV configurations will be erased, and you must re-install each multimedia application.

Use the SmartThings Application as a TV Remote

If you cannot make the Samsung remote function and don’t wish to queue for a repair, you may manage your Television using the Samsung SmartThings application!

Easily install the SmartThings application via the Google Play Store or App Store and create a profile.

Contacting Customer Care

The fourth way to fix a Samsung TV remote that has a blinking red light is to contact Samsung customer service.

If the remote control is still blinking after trying all these steps, it may need to be replaced.

It is important to note that a Samsung TV remote with a blinking red light may not necessarily be broken. If the remote control is blinking correctly, it is recommended that the user consult the user manual or contact Samsung customer service for further assistance.

How to Replace Your Samsung Remote

Suppose your Samsung remote control is blinking continuously. You may need to replace it. Here is how to do so:

• You’ll need to purchase a new Samsung remote control. You can visit the Samsung website or a local electronics store.
• Once you have your new remote, it’s time to pair it with your TV. You’ll need to find the pairing button on your TV to do this. This is usually located within the TV’s settings menu.
• Once you’ve found the pairing button, press and hold it down for a few seconds, then use the new remote to input the code displayed on your TV screen.
• Once the code is entered, your new remote should be paired with your TV. You can now use it to control all of your TV’s functions.

If your new remote blinks correctly, you may need to reset it. To do this, you’ll need to press and hold the pairing button for a few seconds. Then, use the new remote to input the code displayed on your TV screen.

Don’t hesitate to contact Samsung customer support if you have further questions or issues.

When to Call Customer Support for Your Samsung Remote

If your Samsung remote blinks, you can try a few things before calling customer support. First, check the cells and make sure they are correctly installed. If the batteries are low, replace them. If the remote still does not work, try resetting it by holding the power button for five seconds. If the remote still does not work, call Samsung customer support.

How to Prevent Your Samsung Remote from Blinking

If your Samsung remote starts blinking, you can do a few things to troubleshoot the issue.

First, check the cells to ensure they are correctly seated and have plenty of power. If the cells are low, try replacing them. If the controller still does not function, try resetting the remote by holding down the TV and POWER buttons for three seconds. If nothing works, contact Samsung customer support.

Additionally, you can try using the remote with a different TV to see if it is the remote or the TV that is the issue.

Final Verdict

There are many explanations for why your Samsung remote may be blinking. The most common reasons are listed above. If you have followed all the troubleshooting steps and your remote still does not work, you may need to purchase a new remote.

You might want to see this:

• How To Connect Google Home To Samsung Smart Tv
• List of Best Samsung Smartthings Compatible Devices for Your Smart Home

Frequently Asked Questions:

Why is my Remote light continuously blinking?

This light suggests that there is a problem with the device or that the remote is out of reach or the battery is low.

Why is my Samsung remote not available?

Turn off your TV and let the power totally drain if your Samsung remote keeps stating that it is not available. Once you’ve finished, switch the TV back on while pressing the “Return” and “Play/Pause” buttons on the remote control at the same time.