Roku Remote Not Working With New Batteries – Solutions

Nothing is more annoying than settling in to watch your favorite program or movie only to discover that your Roku remote Not Working. The most typical route for troubleshooting, replacing with new batteries. However the issue still exists. That brings up some issues, and you probably came here to hunt for solutions.

You’re in the proper location! I can see how a minor hiccup could ruin a seamless streaming experience. But don’t panic; there are many other potential causes of your Roku remote’s misbehavior, and I’m here to guide you through them.

This tutorial will bring you through useful, simple troubleshooting procedures based on my prior expertise and understanding of the Roku ecosystem.

A Guide on How To Fix Roku Remote Not Working With New Batteries 

Possible Reasons Explanation What To Do
Replaced with incorrect batteries


Each Roku remote compatible with their certain type of battery such as few use AAA and Few Use AA. The correct battery requirements are listed on the remote’s back.
Possibly Interfering HDMI Particularly with regard to Roku streaming sticks that plug directly into the HDMI port on your TV, some Roku remote models may be affected by the interference from surrounding HDMI cables. To avoid interference, try moving your streaming stick away from the HDMI port on your TV using an HDMI cable extender.


Try removing it from the port and replacing it, then retest.

Wi-Fi Connection Problem The Roku remote requires a working local network but does not require an internet connection to connect to your box. Troubleshoot connection with Roku device and Router settings. (after reset the Wi-Fi still not connecting)
Faulty Remote Even with new batteries the remote will not work. Replacement Required

If The Above Solutions Are Not Working Then You Need To See Below Methods:

Re-Pair Your Roku Remote

A Roku remote can occasionally separate from its companion box and become unresponsive. This might occur as a result of system updates, power fluctuations, changes to the Wi-Fi network, using a different Roku box with the device, or even a minor technical issue.

Here’s How You Can Re-Pair Your Remote with Your Roku Device:

  • Disconnect the power supply from your Roku device.
  • Wait for about 10 seconds before reconnecting it. Hold on until the Home page has loaded.
  • Now, it’s time to locate the pairing button on your remote. You can typically find this either on the front of the device or inside the battery compartment. (When you don’t find a pairing button)
  • Press and hold the pairing button for approximately five seconds or until you notice the remote blinking. This shows that the pairing procedure has started.

Keep in mind that some older Roku models don’t use Wi-Fi, but rather an IR pointer. If you own an IR Roku remote and it’s not functioning, ensure that no debris obstructs the receiver on the remote or the Roku box/TV. Make sure that nothing physical is in the way of the remote’s line of sight to the Roku device.

Remember: Re-pairing is pretty basic and takes only a few moments. In many cases, this might be all you need to get your Roku remote back in action!

Roku Remote Not Working With New Batteries
Roku Remote Without Pair Button

Perform a Roku Remote Hard Reset

Try resetting your Roku remote if pairing it again didn’t resolve the problem. This requires taking particular actions as the Roku device boots up. This is how you do it:

  • Your Roku remote’s batteries should be removed.
  • Your Roku device’s power cord should be unplugged (or, if you have a working IR remote, go to Settings > System > System Restart > Restart).
  • Prior to reconnecting your Roku device to the power, give it a few seconds to wait.
  • Replace the batteries in your Roku control once the Home screen has loaded.
Roku Remote Not Working With New Batteries
Roku Remote With Pair Button

Using Button (Older Models)

  1. Remove all cables except the Power cord.
  2. Press and hold the “Reset” button on the back or bottom of the device for about 20 seconds. Some models will require a paper clip to press the button.
  3. Continue to hold the “Reset” button, then remove the Power cord from the back of the unit.
  4. Release the “Reset” button, then plug all of the cords back into the device.

 A Detail Guide on Resetting Roku will be helpful in case you unable to perform it by following above method.

Further Repair Advice for Your Roku Remote

Here are some more emergency solutions for your Roku remote issue.

Drain the battery on your Roku remote. Place the batteries back in, press and hold any button on the remote for 10 to 30 seconds, and then test it. Electronics occasionally experience shorts due to aberrant charge buildup in parts.

The problem with your remote could be a hardware one, such as a corroded connection on the circuit board. If you’re mechanically inclined, disassemble the remote and examine it for burn marks, corrosion buildup, or other signs of a problem.

If corrosion is discovered, such as that caused by moisture or another factor, carefully remove the debris with a toothbrush and rubbing alcohol before reassembling the remote and allowing it to dry for at least 30 seconds. Any warranty you may have had on the remote will be void as a result of this action.

How to Connect Roku Device without a Roku Remote?

There are other ways you can manage your Roku device without remote or remote not working by following different methods:

Last Resort – Replacement Remote

If all else fails to fix the issue of Roku not responding to remote and you’ve exhausted the prior troubleshooting options, consider getting a new remote. Roku remotes are reasonably priced and easily accessible on a variety of online retail websites.

Make sure the new remote is compatible with your exact Roku model before purchasing a replacement. This is a crucial step because not every remote is compatible with every Roku device.

Find the top The Top Roku Devices In 2023

Frequently Asked Questions:

What is a Roku remote reset code mean?

It’s a soft reset which means that after resetting all data and setting will not be lost after soft reset.

  • Home Press Five times
  • Up Press one time
  • Rewind Press Two times
  • Fast Forward Press Two times


Choose System > System Restart > Restart. If frozen, press Home button 5 times + up arrow + Rewind + Fast Forward.

This should work on all Roku models.

Can my Roku remote be upgraded?

Yes! You can upgrade the remote on an older Roku device without replacing the Roku box if you desire the voice control capability. You should check for compatibility before buying a remote because some of them are incompatible with much older Roku devices.

What kind of batteries does a Roku control ask for?

Numerous Roku remote controls require two AAA or AA batteries. The correct battery requirements are listed on the remote’s back.

Roku Remote Not Working With New Batteries
Battery Compartment
0/5 (0 Reviews)

About The Author

Hassan Zaka

I am an expert in accounting and possess diverse experience in technical writing. I have written for various industries on topics such as finance, business, and technology. My writing style is clear and simple, and I utilize infographics and diagrams to make my writing more engaging. I can be a valuable asset to any organization in need of technical writing services.

Follow Us:

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top