How to Reprogram Chamberlain Garage Door Keypad

The procedure of How to reprogram the chamberlain garage door keypad is very simple and easy, first, you need to erase all previous memory before reprogramming the door keypad.

Here are the Steps of How to Reset Chamberlain Garage Door opener:

How to erase it?

  • Locate the LEARN button on the garage door opener.
  • Press and hold the LEARN button on the door control until the LED turns off (approximately 6 seconds).
  • All previous codes are now erased. Reprogram each remote control and keypad you wish to use

Note: If you want to double-check that you’ve correctly reset your opener, you can use the remote that’s connected with it. There should be no response from the door.

Reconnect your Remote Control

After resetting the Chamberlain garage door opener, the remote must be reconnected.

The model of your opener and the color of the LEARN button on your opener will determine the specific actions you must take.

reset chamberlain garage door opener

Follow these steps to connect your Chamberlain remote control:

1) Detach the remote control’s metal clip. That’s how you’ll find the tiny button in the middle of the back of your remote (on newer models that reset button may be located on the front or side of the remote).
2) Push that button with the metal clip.
3) An LED light should now be visible on the top of your remote.

More Recent Versions

4) The garage door opener’s LEARN button must be pressed and held down for a few seconds. The corresponding led light, labelled “LEARN,” will glow. In less than a minute…
5) Press and then release the desired remote control button.
6) Examine the garage door opener’s light bulb to see whether it flashes. If not, push and hold the remote control button until the LED lights up steadily, then try again.
7) Do this again and again until the light bulb blinks. After the light has blinking, DO NOT press the button!

Aged Models

4) Find the LEARN button on the casing of your Chamberlain motor and note its color. Follow the above table to press and RELEASE the desired remote button for the required amount of times.
5) Press a different button on the remote just once after the required amount of presses. The remote’s LED light should now go dark.
6) Now, push and hold the LEARN button on the motor housing of your Chamberlain opener.
7) Once you’ve finished programming the remote, push the button once to make the opener’s light flash; press it again to open or close the garage door.

Then Reprogram Chamberlain Garage Door Keypad as follows:

To set up your Chamberlain keypad:

1) The Chamberlain garage door opener can be programmed by pressing the LEARN button on the motor housing.
2) You’ll have 30 seconds to get the keypad set up after the LED light comes on.
3) Enter your 4-digit code and press and hold the ENTER key until you hear a click and the light on the overhead panel flashes. Casing for Chamberlain garage door motors
4) Simply pressing ENTER will cause the garage door to close.
5) Enter your 4-digit code and hit ENTER when the door has closed. The door to your garage must now open.
Note: If your keypad still isn’t working after following the above steps, it may be interfering with other remote controls you have in your vehicles.

This Procedure is for MODELS 940EV, 940EV-P2, 940EVC AND 940EVC-P2

1- Press and hold the * and # buttons until the lights on the keypad stop blinking.

How to Reprogram Chamberlain Garage Door Keypad

2- Enter a 4-digit personal identification number (PIN) of your choice, then press the # button.

2 4

3- Press and release the ENTER button on the Keyless Entry the number of times that corresponds with your garage door opener type:

3 4

4- Press and release the 0 buttons.

4 4

5- Press and release the Learn button on the garage door opener. The Learn LED will light. Within 30 seconds…

How to Reprogram Chamberlain Garage Door Keypad

6- Enter your 4-digit PIN, then press and release the ENTER button until the garage door opener lights flash or two clicks are heard.

6 1

7- To test, enter your PIN, then press the ENTER button. The garage door opener will activate.

How to Reprogram Chamberlain Garage Door Keypad 1

In addition to that there are other models of chamberlain keypad and how to program and reprogram Chamberlain Garage Door Keypad of 376LM, 376LMC, 377LM, 377LMC, 877LM, 940LM, 940D, 940ESTD, 976LM, and 976LMC.

  • To reprogram you need to erase an all old memory:
  • To do that follow the above procedure of how to erase it, after following a erasing procedure…

First Time Programming: Chamberlain Keypad Programming

Relevant: How to Reset Chamberlain Garage Door Keypad Without Enter Button

Reprogram it:

Programming a Keypad PIN

The two (2) options to program a 4-digit Personal Identification Number (PIN) include using a door control with a LEARN button or using a garage door opener with a LEARN button.

Program a Keypad PIN Using Your Door Control

  1. Be sure to clear the garage door area of any obstructions.
  2. Locate the LEARN button on the door control.
  3. Press the LEARN button twice. The LED will flash.
  4. Enter a 4-digit PIN of your choice on the keypad, and press ENTER.
  5. The opener lights will blink, indicating the PIN programming is complete.

Once your PIN is set, you can change the PIN or set a temporary PIN (Procedure to do that are in a later section).

Program Garage Door Keypad PIN Using Your Garage Door Opener

  1. Be sure to clear the garage door area of any obstructions.
  2. Locate the LEARN button on the garage door opener. Press and release the LEARN button. Once the LED is lit, you will have 30 seconds to complete the next step.
  3. Enter a 4-digit PIN of your choice, then press and hold the ENTER button until the garage door opener light blinks. The PIN programming is complete.

How to Change Code on Chamberlain Garage Door Opener

Here are the basic steps for changing an existing keypad personal identification number (PIN).

  1. Be sure to clear the garage door area of any obstructions.
  2. Press the programmed PIN that you want to change.
  3. Press and hold the # button until the garage door opener light blinks twice.
  4. Enter the new 4-digit code of your choice, then press the ENTER button. The opener lights will blink once. The PIN programming is complete

Add a Temporary PIN

  1. Enter any programmed PIN, then press and hold the * button until the garage door opener light blinks three times.
  2. Enter the temporary 4-digit PIN, different than the last one you used, then press the ENTER button. The garage door opener lights will blink four times
  3. Press the number of hours the temporary PIN will work (up to 255 hours), then press the * button. The garage door opener blinks one time, and the temporary PIN is ready to use.

Set How Many Times to Open the Garage Door with a Temporary PIN

  1. Enter any programmed PIN, then press and hold the * button until the garage door opener light blinks three times.
  2. Enter the temporary 4-digit PIN of your choice, then press the ENTER button. The garage door opener lights will blink four times.
  3. Press the number of times the temporary PIN will work (up to 255 openings), then press the # button. The garage door opener blinks one time, and the temporary PIN is ready to use.

Support

If you’re still stuck, you can call Chamberlain directly at 1-(800)-528-5880. They should be able to make things right. Their hours are:

  • Monday – Friday: 8:00am – 9:00pm EDT
  • Saturday: 10:00am – 7:00pm EDT
  • Sunday: CLOSED

Chamberlain Manuals

If you’d rather not wait in a call queue, you can find a wealth of useful information on the Chamberlain website.

Check the motor housing of your Chamberlain garage door opener for a sticker that will tell you what model you have.

0/5 (0 Reviews)

About The Author

Hassan Zaka

I am an expert in accounting and possess diverse experience in technical writing. I have written for various industries on topics such as finance, business, and technology. My writing style is clear and simple, and I utilize infographics and diagrams to make my writing more engaging. I can be a valuable asset to any organization in need of technical writing services.

Follow Us:
LinkedinTwitter

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top